Classic Manuel Powder Coating Equipment

With its special design, high quality and reliability properties, classic powder coating equipment faces all of customer requirements. Moreover, its special ergonomic design and high productive capacity provides customers an easy usage while assuring better efficiency. You can check further technical descriptions of equipment and its electro pneumatic control panel below.

Standard Manuel Powder Coating Equipment

MG3000 Manual Power Coating Gun

Automatic Powder Coating Equipment

Powder Coating Reciprocator Of Plc Control

AG3000 Automatic Powder Coating Gun

Automatic Powder Coating Booths

Automatic Powder Spraying Booths, which take very tight space and suitable to color change quickly, with filter, monocyclone or multicyclone types, are used with conveyor type lines.

Their material is iron sheet or galvanize or stainless steel. Paint feeding is directly to the guns by a fine sieve under filter type booths and gaining back system beside cyclone type booths.

Manual Powder Coating Booth

This booth is dizayn for Manual effect. It is designed in order to paint both medium size parts such as metallic goods and too long parts, and suitable to change rapid color change.

All parts of the booth are disassembled and can be mounted by screw and dismounted easily, if required.

We produce manual booths in different sizes or filter types depending to customer needs.

Multi - Cyclone Powder Pinting Units

Manual Tribo Powder Coating Machine

The Powder Coating Gun Of The Tribo System

Tribo Automatic Powder Coating Equipment

Automatic Tribo Powder Spray Gun

With its special design, high quality and reliability, strong3000 registered branded automatic tribo systems face all of customer desires and offer ideal solutions for application of powder coating.

Dipping Type Surface Treatment Line

The system consists of chemical tanks, drying tank, monorail crane system and the basket where the parts to which the surface treatment will be applied are placed. It is based on holding for a period of time equal to the process time upon immersing into the chemical inside the tanks. Its advantage compared to the spraying applications is that it provides equal cleaning and coating facility by penetrating onto each part of the materials equally (products such as profile and pipe). Materials must be dried fast upon completion of the process.

Spray Type Surface Treatment Line

In case of high production capacity, the systems with spray lines are more economical. The parts moving as hung onto the conveyor in this system pass through active sections inside spray unit and react to the chemicals under proper time, pressure, flow and temperature. The length of the spray tunnel depends on the process to be applied and the conveyor speed.

The materials of the bath tanks and tunnel are manufactured by Cr-Ni, Black sheet-iron or plastic material according to the process to be applied.

Box Curing Oven

The furnace consists of sandwich panels which have rock wool and yellow as the insulation material between inner side of 1,2mm galvanized steel and outer side of 1,2 mm mild steel sheet. The walls and the ceiling of the oven are 50 mm rock wool and 100 mm yellow insulation total thickness 150 mm and its base is 50 mm thickness. There are adjustable type air blowing mouths and air circulation ducts which homogeneously distribute air at 200 °C. Heat control device is digital type. The heat of the oven is controlled by the command of the thermostat that works by the signal of the thermo-couple, to the burner. Air seal and curtains of the entrance and exit of the oven prevent hot air leakage from the oven. Adjustable type digital thermostats, thermo-couples, consuls carrying the conveyor passing through the oven cable lines to the burner, fans, cable channel and electrical control panel are included in the system.

According to project burn room is assemble to back, side and over of oven and thermo-unit is fitted at the side of the furnace and has the capacity of increasing the furnace temperature up to 250°C. Firing part of the heating unit is produced from SAE316 stainless steel. Unit body from mild steel and heat-insulated. This unit includes an explosion door against explosion, a burner, a circulating fan, an observation cover and electrical installations.

Tunnel Type Curing Oven

The furnace consists of sandwich panels which have rock wool and yellow as the insulation material between inner side of 1,2mm galvanized steel and outer side of 1,2 mm mild steel sheet. The walls and the ceiling of the oven are 50 mm rock wool and 100 mm yellow insulation total thickness 150 mm and its base is 50 mm thickness. There are adjustable type air blowing mouths and air circulation ducts which homogeneously distribute air at 200 °C. Heat control device is digital type. The heat of the oven is controlled by the command of the thermostat that works by the signal of the thermo-couple, to the burner. Air seal and curtains of the entrance and exit of the oven prevent hot air leakage from the oven. Adjustable type digital thermostats, thermo-couples, consuls carrying the conveyor passing through the oven cable lines to the burner, fans, cable channel and electrical control panel are included in the system.

According to project burn room is assemble to back, side and over of oven and thermo-unit is fitted at the side of the furnace and has the capacity of increasing the furnace temperature up to 250°C. Firing part of the heating unit is produced from SAE316 stainless steel. Unit body from mild steel and heat-insulated. This unit includes an explosion door against explosion, a burner, a circulating fan, an observation cover and electrical installations.

U type Curing Oven

The furnace consists of sandwich panels which have rock wool and yellow as the insulation material between inner side of 1,2mm galvanized steel and outer side of 1,2 mm mild steel sheet. The walls and the ceiling of the oven are 50 mm rock wool and 100 mm yellow insulation total thickness 150 mm and its base is 50 mm thickness. There are adjustable type air blowing mouths and air circulation ducts which homogeneously distribute air at 200 °C. Heat control device is digital type. The heat of the oven is controlled by the command of the thermostat that works by the signal of the thermo-couple, to the burner. Air seal and curtains of the entrance and exit of the oven prevent hot air leakage from the oven. Adjustable type digital thermostats, thermo-couples, consuls carrying the conveyor passing through the oven cable lines to the burner, fans, cable channel and electrical control panel are included in the system.

According to project burn room is assemble to back, side and over of oven and thermo-unit is fitted at the side of the furnace and has the capacity of increasing the furnace temperature up to 250°C. Firing part of the heating unit is produced from SAE316 stainless steel. Unit body from mild steel and heat-insulated. This unit includes an explosion door against explosion, a burner, a circulating fan, an observation cover and electrical installations.

Curing Oven With Over Conveyor

The furnace consists of sandwich panels which have rock wool and yellow as the insulation material between inner side of 1,2mm galvanized steel and outer side of 1,2 mm mild steel sheet. The walls and the ceiling of the oven are 50 mm rock wool and 100 mm yellow insulation total thickness 150 mm and its base is 50 mm thickness. There are adjustable type air blowing mouths and air circulation ducts which homogeneously distribute air at 200 °C. Heat control device is digital type. The heat of the oven is controlled by the command of the thermostat that works by the signal of the thermo-couple, to the burner. Air seal and curtains of the entrance and exit of the oven prevent hot air leakage from the oven. Adjustable type digital thermostats, thermo-couples, consuls carrying the conveyor passing through the oven cable lines to the burner, fans, cable channel and electrical control panel are included in the system.

According to project burn room is assemble to back, side and over of oven and thermo-unit is fitted at the side of the furnace and has the capacity of increasing the furnace temperature up to 250°C. Firing part of the heating unit is produced from SAE316 stainless steel. Unit body from mild steel and heat-insulated. This unit includes an explosion door against explosion, a burner, a circulating fan, an observation cover and electrical installations.

Power Curing Oven

The furnace consists of sandwich panels which have rock wool and yellow as the insulation material between inner side of 1,2mm galvanized steel and outer side of 1,2 mm mild steel sheet. The walls and the ceiling of the oven are 50 mm rock wool and 100 mm yellow insulation total thickness 150 mm and its base is 50 mm thickness. There are adjustable type air blowing mouths and air circulation ducts which homogeneously distribute air at 200 °C. Heat control device is digital type. The heat of the oven is controlled by the command of the thermostat that works by the signal of the thermo-couple, to the burner. Air seal and curtains of the entrance and exit of the oven prevent hot air leakage from the oven. Adjustable type digital thermostats, thermo-couples, consuls carrying the conveyor passing through the oven cable lines to the burner, fans, cable channel and electrical control panel are included in the system.

According to project burn room is assemble to back, side and over of oven and thermo-unit is fitted at the side of the furnace and has the capacity of increasing the furnace temperature up to 250°C. Firing part of the heating unit is produced from SAE316 stainless steel. Unit body from mild steel and heat-insulated. This unit includes an explosion door against explosion, a burner, a circulating fan, an observation cover and electrical installations.